Ponoko

Leather (Vege Tanned) - Auburn

0.098 inches

Auburn-leather-5_large
There are 5 images for this material

What is it

Natural, vegetable tanned leather.

How fast will this material ship?

Orders using this material will ship as fast as same day. Find out more.

Can I get a sample?

You can get a sample here.

Design Notes

Full grain leather with a smooth finish on one side and a coarse finish on the other. Can be oiled to improve water resistance. Some natural imperfections could appear on the surface of the leather.

Unlike other materials leather will be shipped without the surrounding material sheet. The sticky paper we normally use to hold all cut pieces within the surrounding material can damage the surface of the leather so we opt to individually pull designs off the laser and bag them for shipping. Add a cutting line around all pieces of the leather that you want to have shipped.

The manufacturers tolerance for the thickness of the material is as follows:

Material thicknessPossible Range
inchesmm
0.098" / 2.5mm0.084” - 0.113”2.1 - 2.9mm


Engraving Leather

Leather will turn brown and powdery when engraved so large areas of engraving are not recommended. Line engraving produces crisp results and is recommended over area engraving

There are 3 types of engraving possible with laser cutting - area engraving, line engraving and a combination of both.

Area engraving is great it you need to mark a large area on the surface of the material. To specify area engraving set your shapes to have a fill color of black with RGB values of 0, 0, 0. The way this engraving is performed is like an old dot matrix printer except instead of dots of ink it uses pulses of the laser beam. This is a surface finish not deep enough to be used for pocketing or inlays. The depth of the engraving ranges between 0.1-0.5mm.

Line engraving is like a really shallow cut. To achieve this effect the stroke color to red with RGB values of 255, 0, 0 and set the stroke style to a width of 0.01 mm. The laser beam follows along the red lines that you have in your design and marks the surface of the material. The result is crisp but it can be a time consuming technique if you have a lot of small details like text.

Using a combination of both engraving types typically gets the best result. Set your shapes to have a fill color of black with RGB values of 0, 0, 0, the stroke color to red with RGB values of 255, 0, 0, and set the stroke style to a width of 0.01 mm. The line engraving causes the laser beam to trace around the edges of the engraved areas making them more crisp and bringing the details to life.

Typical Uses

Leather is typically used for crafts, jewelry, wallets, cuffs, table mats, coasters, handcraft, belts, etc.

Environmental Information

Leather is tanned using tannin and other ingredients found in vegetable matter, tree bark, and other such sources.

Adhesives, joints and fastenings

Rivets and common sewing techniques will work for joining this material.

Laser cut thread holes and pieces can be stitched neatly by hand.

Tips from other designers

None-set-small
Ankit says:

What glue we can use on the textile backing on leather back side for reinforcement (being laser cut), so that glue can evaporate from stitch holes and doesn't give leather a bad look by remaining in stitch holes...???

Added about 1 year ago. ( delete )
578860_10150999241441032_253901805_n_small
Dayma says:

Hi Ankit. We're having a little trouble understanding your question. Are you asking if we can please use a glue when laser cutting the leather to try and give the leather a better look when finished? Can you please reframe the question clearly.

Currently we use protective tape on the back of leather when laser cutting it. The charred finish (We think you're talking about) on the edges of the leather are unavoidable when laser cutting. Since it's a laser beam cutting through a natural material.

Added about 1 year ago. ( delete )
None-set-small
Ian says:

Is it possible to cut a design right through the leather?

Added 7 months ago. ( delete )
578860_10150999241441032_253901805_n_small
Dayma says:

Hi Ian,

Yes, definitely. When you create your design and add a cutting line, it will cut through the material. Please make sure to read how to set up you design file correctly - http://www.ponoko.com/make-and-sell/design-it-yourself

Thanks

Added 7 months ago. ( delete )

Sign up for our newsletter
to get special offers: